How Do You Move a MEMS Device From Prototype to Volume at a MEMS Foundry?
Note Title

http://linqto.me/n/StefanReilly
Note URL

Content:

Rhea’s pressure sensor worked on the bench. She had five hand assembled units, a happy investor and a new problem: a customer wanted five thousand. That jump terrified her, because making five and making five thousand are different jobs. The path between them runs through a MEMS foundry, and the order of steps matters more than most people expect.

InchFab’s pages claim support from early development to volume production, with modular lines built for different lifecycle stages. This article lays out a sensible route from prototype to volume, using those pages as a reference, and points out the questions that quietly decide whether the climb goes smoothly or turns into a painful scramble.

Why Is the Jump So Hard?

A prototype can survive hand tuning. A production run can’t. Variation that was invisible across five units shows up across five thousand. Film thickness drifts, etch depth wanders and seals leak at a low but real rate. Each small effect multiplies at scale, and nobody can fix them one by one.

So the real task isn’t only making more. It’s making a process that behaves the same way every time. That means measuring, controlling and documenting. It’s less glamorous than design work, and it’s where many promising MEMS products quietly fail, usually after the excitement has faded.

What Does InchFab Say About the Path?

The Foundry Service page says InchFab supports customers at every stage, from early development with turnaround as fast as one week to volume production with cost per chip that holds up against traditional 200mm to 300mm foundries. The InchFab Line page describes a portfolio of modular lines, each engineered for a specific lifecycle stage.

Those are the company’s statements, so treat them as questions to test. Ask what changes between the development line and the production line, whether the process transfers directly and who handles the transition. A confident answer should include steps, not slogans. Rhea asked for a written plan and got one within days.

How Do You Lock the Process?

First, freeze the design. Endless tweaks are fine in prototyping and fatal in process development services production. Pick a version, test it and agree what counts as good. Write the targets down: thickness windows, etch depths, resistance ranges, leak rates. Those numbers become the contract between you and the factory.

Second, use test structures on every wafer. The Foundry Service page lists process monitor chips, test structures and design rule check vehicles. A few small patterns per wafer let you check the process lot after lot without cutting open real devices. It’s cheap insurance, and it makes trends visible before they become problems.

Which Measurements Matter Most?

Film thickness, etch depth, line width and electrical contact quality usually top the list. The InchFab Line page lists a laser confocal tool, a white light interferometer and a reflectometer, which cover height and thickness checks. Ask how often each is used and whether the data comes back to you.

Rhea asked for measurement results after every critical step, not just at the end. The team agreed, and she spotted a slow drift in a film within the second lot. Catching that in week three saved her from discovering it in a customer’s complaint months later.

How Do Cost and Yield Change?

Cost per chip depends on how many good chips come from each wafer. Raise yield and the cost drops, even if wafer cost stays the same. That’s why the Foundry Service page lists lowest cost and highest yield as two of its four promises, next to fastest cycle time and highest flexibility.

Again, those are claims. Ask for real yield numbers on a device like yours, and ask how they were measured. Also ask what happens to cost as volume grows, and where the knees in the curve are. A good provider can sketch that curve for you without much fuss.

What Role Does Packaging Play?

A bare MEMS chip isn’t a product. It needs a package, connections and often a protective opening. The Foundry Service page lists wafer level chip scale packages, redistribution layers, through silicon vias, copper pillar arrays and fan out options. Pick your packaging plan early, because it shapes die size and layout.

If you plan to use wafer level packaging, say so in your first conversation with any MEMS foundry you’re considering. It can change the process flow and the schedule. Rhea’s packaging choice moved two of her layout decisions, and she was glad she’d raised it before the masks were final.

What Should You Plan for Facilities and Supply?

If you only send wafers to a foundry, facilities are the foundry’s problem. If you run your own line, they become yours. The InchFab Line page lists 100mm wafers, a 50 by 24 by 15 foot fab, 2 meters of clearance and utilities including 220V power at 400A, 7.5 ton HVAC and a DI water plant.

Supply matters too. Ask about lead times for wafers and materials, and about backup options if something runs short. Pages don’t cover this, so raise it directly. Rhea made a short list of risks, from materials to staffing, and ranked them. It sounded dull in the meeting and saved her a week later.

Who Owns Each Piece?

Write down who is responsible for what: process, measurement, packaging, testing and delivery. Ask about intellectual property and process documentation, since the pages I read don’t state a policy. You want a written recipe you can reuse, not knowledge that lives in one engineer’s head.

Use the contact page or . Get answers in writing. If a provider hesitates on documentation or ownership, slow down. The best partners treat those questions as normal, and they answer without making you feel like you’ve insulted anybody.

So, How Does Rhea’s Story End?

She isn’t at five thousand yet. She’s at a few hundred, with a frozen design, a measurement plan and a packaging route. That’s real progress, and it came from slow, careful steps instead of one heroic push. The customer is still waiting, and still patient, because she keeps sending honest updates.

If you’re facing the same jump, freeze the design, measure everything, plan packaging early and write down who owns what. None of it is exciting, and all of it works. A good partner will help you climb steadily, and a bad one will promise you the summit and vanish at the first storm.

FAQs

Does InchFab support volume production?
The pages say it supports customers from early development to volume production.

What measurement tools are listed?
A laser confocal tool, a white light interferometer and a reflectometer.

Which packaging options are listed?
Wafer level chip scale packages, redistribution layers, through silicon vias, copper pillar arrays and fan out packages, among others.

Does InchFab publish yield data?
Not on the pages I read, so ask the team.

 

Keywords (Tags):  
No keywords provided.






Share note:   

Email note:    
   

Created by:    CrystalWebster
 
Created on:   

Hits:   3
Why Join?  | Contact Us  | Linqto.me - all rights reserved. Version 9.5.11.76